How to factory reset Linksys WRT1900AC v2 router – Default Login & Password

The Linksys WRT1900AC v2 router has Gigabit WiFi, 4 Gigabit ETH-ports and 0 USB-ports.
It is also known as the Linksys AC1900 Dual-Band Smart Wi-Fi Wireless Router – Cobra. It also supports custom firmwares like: OpenWrt, LEDE Project
The WRT1900AC v2 is featured in our
Best Mid-end routers: buying guide
How to factory reset Linksys WRT1900AC v2 - Default Login & Password

Linksys WRT1900AC v2 default Password , Login & Gateway settings :

If you have performed a reset of your WRT1900AC v2 device or not changed the defaults, you
should
be able to access it with the following settings
Default subnet mask: 255.255.255.0

How to factory reset (hard reset) Linksys WRT1900AC v2 :

You can factory reset your Linksys WRT1900AC v2 in the following way(s)
Through the web interface
Open your browser and navigate to the router interface (see default settings below)
Under the Administration tab you will find a sub-tab called Factory defaults
On the Factory defaults page click the button labeled Restore Factory Defaults
With the reset button
Have your unit powered on
Press and hold the reset button for at least 10 seconds until the power light starts blinking, then release.
When the power light goes solid, unplug the power to the router for 10 seconds
Plug the power back in and start the router
When the power light goes solid again the router is ready to use.

Linksys WRT1900AC v2 router specifications :

System specs
CPU: 1.3 GHz
RAM: 512 MiB
Flash: 128 MiB
Custom firmwares: OpenWrt, LEDE Project
Connectivity
WiFi: Gigabit (abgn+ac)
WiFi bands
2.4GHz & 5GHz
WiFi throughput: n/a
WAN
1 x Gigabit port
ETH
4 x Gigabit ports
USB-ports: 0
Linksys WRT1900AC review (quick overview)
Here is the quick comparison of how the Linksys WRT1900AC compares to
other routers on our site
Average
55/100
Editor
92/100
WiFi
20/100
Hardware
55/100
Current price
$75.51
For a full list of routers and how they compare to the WRT1900AC v2, check the
Router Buying Guide which will help you buy the most
price-competitive router.
WRT1900AC v2 Firmwares
Staying up to date with the latest firmware is a good idea to keep your router even more
secure
from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider
flashing
an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly
increase
the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Linksys WRT1900AC v2
Flashing OpenWrt on the Linksys WRT1900AC v2
The Linksys WRT1900AC v2 is supported by OpenWrt according to their Table of
Hardware. So
flashing OpenWrt onto it should be quite straigthforward.
We couldn’t find any specific instructions for flashin OpenWrt on the Linksys
WRT1900AC v2, but since it’s listed in their Table of Hardware as supported, you can
head
over to the
OpenWrt install instructions and read on there.
Note: Flashing custom firmwares is always on you’re on own risk. Make sure to
read OpenWrt’s wikis to understand the risks and how to proceed if something goes
wrong.
Flashing LEDE Project on the WRT1900AC v2
The Linksys WRT1900AC v2 is also supported by the LEDE Project.
To install LEDE aquire the correct firmware from their
Firmware downloads page and
then follow the instructions on their
Quick Start Guide
Note: Make sure to read the LEDE wikis carefully before flashing.
Linksys stock firmware for the WRT1900AC v2
Stock firmwares for the WRT1900AC v2 are available under the download section on the
modem’s
support page. You can also refer
to the router’s manual for instructions on how to upgrade the firmware.