How to factory reset TP-LINK TL-WR941ND v3.x router – Default Login & Password

The TP-LINK TL-WR941ND v3.x router has 300mbps WiFi, 4 100mbps ETH-ports and 0 USB-ports.
It is also known as the TP-LINK 300Mbps Wireless N Router. It also supports custom firmwares like: OpenWrt, LEDE Project
How to factory reset TP-LINK TL-WR941ND v3.x - Default Login & Password

TP-LINK TL-WR941ND v3.x default Password , Login & Gateway settings :

Default Gateway IP: 192.168.1.1
Default username: admin
Default password: admin
Default subnet mask: 255.255.255.0
Default DNS server: 192.168.1.1

How to factory reset (hard reset) TP-LINK TL-WR941ND v3.x :

You can factory reset your TP-LINK TL-WR941ND v3.x in the following way(s)
Through the web interface
Open a browser and navigate to the web interface of the router (see default settings below)
In the menu look for System tools and under there find the Factory defaults option
On the Factory defaults page click on the Restore button to perform the reset.
With the RESET/WPS button
Have the unit powered on
Press and hold the reset (sometimes reset/WPS) button for 10 seconds with a paperclip or other sharp object.
When the SYS led start blinking quickly release the reset button and wait for router to boot back up.

How to login to the TP-LINK TL-WR941ND v3.x :

Make sure you are connected to the router’s network, either by Wi-Fi or ethernet cable.
Open your browser and visit
http://192.168.1.1
You should be prompted with a login dialogue.
Enter the username: admin
and the password admin
You will now be logged in. If you haven’t yet changed the defaul password, we recommend that you change it first
thing you do after logging in.

TP-LINK TL-WR941ND v3.x router specifications :

System specs
CPU: 400 MHz
RAM: 32 MiB
Flash: 4 MiB
Custom firmwares: OpenWrt, LEDE Project
Connectivity
WiFi: 300mbps (bgn)
WiFi bands
n/a
WiFi throughput: n/a
WAN
1 x 100mbps port
ETH
4 x 100mbps ports
USB-ports: 0
TL-WR941ND v3.x Firmwares
Staying up to date with the latest firmware is a good idea to keep your router even more
secure
from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider
flashing
an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly
increase
the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the TP-LINK TL-WR941ND v3.x
Flashing OpenWrt on the TP-LINK TL-WR941ND v3.x
The TP-LINK TL-WR941ND v3.x is supported by OpenWrt according to their Table of
Hardware. So
flashing OpenWrt onto it should be quite straigthforward.
We couldn’t find any specific instructions for flashin OpenWrt on the TP-LINK
TL-WR941ND v3.x, but since it’s listed in their Table of Hardware as supported, you can
head
over to the
OpenWrt install instructions and read on there.
Note: Flashing custom firmwares is always on you’re on own risk. Make sure to
read OpenWrt’s wikis to understand the risks and how to proceed if something goes
wrong.
Flashing LEDE Project on the TL-WR941ND v3.x
The TP-LINK TL-WR941ND v3.x is also supported by the LEDE Project.
To install LEDE aquire the correct firmware from their
Firmware downloads page and
then follow the instructions on their
Quick Start Guide
Note: Make sure to read the LEDE wikis carefully before flashing.

TP Link