How to factory reset Linksys EA4500 v1 (Cisco) router – Default Login & Password

The Linksys EA4500 v1 (Cisco) router has 300mbps WiFi, 4 N/A ETH-ports and 0 USB-ports.
It is also known as the Linksys Dual-Band N900 Router with Gigabit and USB.
How to factory reset Linksys EA4500 v1 (Cisco) - Default Login & Password

Linksys EA4500 v1 (Cisco) default Password , Login & Gateway settings :

Default Gateway IP:
Linksys login instructions
Default username: admin
Linksys router default password list
Default password: admin
Default subnet mask:
Default DNS server:

How to factory reset (hard reset) Linksys EA4500 v1 (Cisco) :

You can factory reset your Linksys EA4500 v1 (Cisco) in the following way(s)
Through the web interface
Open your browser and navigate to the router interface (see default settings below)
Under the Administration tab you will find a sub-tab called Factory defaults
On the Factory defaults page click the button labeled Restore Factory Defaults
With the reset button
Have your unit powered on
Press and hold the reset button for at least 10 seconds until the power light starts blinking, then release.
When the power light goes solid, unplug the power to the router for 10 seconds
Plug the power back in and start the router
When the power light goes solid again the router is ready to use.

How to login to the Linksys EA4500 v1 (Cisco) :

Make sure you are connected to the router’s network, either by Wi-Fi or ethernet cable.
Open your browser and visit
You should be prompted with a login dialogue.
Enter the username: admin
and the password admin
You will now be logged in. If you haven’t yet changed the defaul password, we recommend that you change it first
thing you do after logging in.

Linksys EA4500 v1 (Cisco) router specifications :

System specs
CPU: 1.2 GHz
RAM: 128 MiB
Flash: 128 MiB
Custom firmwares: OpenWrt
WiFi: 300mbps (abgn)
WiFi bands
2.4GHz & 5GHz
WiFi throughput: n/a
1 x N/A port
4 x N/A ports
USB-ports: 0
Linksys EA4500 review (quick overview)
Here is the quick comparison of how the Linksys EA4500 compares to
other routers on our site
Current price
For a full list of routers and how they compare to the EA4500 v1 (Cisco), check the
Router Buying Guide which will help you buy the most
price-competitive router.
EA4500 v1 (Cisco) Firmwares
Staying up to date with the latest firmware is a good idea to keep your router even more
from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider
an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly
the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Linksys EA4500 v1 (Cisco)
Flashing OpenWrt on the Linksys EA4500 v1 (Cisco)
The Linksys EA4500 v1 (Cisco) is supported by OpenWrt according to their Table of
Hardware. So
flashing OpenWrt onto it should be quite straigthforward.
We couldn’t find any specific instructions for flashin OpenWrt on the Linksys
EA4500 v1 (Cisco), but since it’s listed in their Table of Hardware as supported, you can
over to the
OpenWrt install instructions and read on there.
Note: Flashing custom firmwares is always on you’re on own risk. Make sure to
read OpenWrt’s wikis to understand the risks and how to proceed if something goes
Linksys stock firmware for the EA4500 v1 (Cisco)
Stock firmwares for the EA4500 v1 (Cisco) are available under the download section on the
support page. You can also refer
to the router’s manual for instructions on how to upgrade the firmware.